|
|
|
|
|
|
|
|
|
Modification |
Status | ||
| Suspension/Handling: | ||||
| G2 adjustable panhard bar | (removed) | |||
| Adjustable panhard bar, Road Tech. | ||||
| G2 4 point engine bay brace | ||||
| G2 anti-sway bars | ||||
| G2 Torque Arm | ||||
| Hotchkis trailing arms | ||||
| G2 Drive Shaft Loop | (to be installed) | |||
| IRS Terminator subframe connectors | ||||
| Prothane end link bushings | ||||
| Energy Suspension motor mounts | ||||
| Energy Suspension trans. mount | ||||
| Energy Suspension front control arm bushings | ||||
| Eibach Pro Kit suspension springs | (removed) | |||
| Sumotomo 245/50ZR16 | ||||
| Functional/Convenience: | ||||
| B & M Ripper shifter | ||||
| CAGS "Skip Shift" disabled | ||||
| CAGS "Skip Shift" indicator disabled | ||||
| Auto Meter Dual guage pod | (to be installed) | |||
| Auto Meter Z series 2" boost gauge | (to be installed) | |||
| Intellitronix Air/Fuel ratio guage | (never installed) | |||
| Auto Meter Quick-Shift Lite | (to be installed) | |||
| Summit RPM Activation Switch | (to be installed) | |||
| Engine/Short Block: | ||||
|
Callies "Stealth" (= to Racemaster) forged steel crankshaft 3.750" stroke s/n 37440 / 3750 casting 7AA |
||||
| Callies forged rods, 5.850 length. | ||||
|
JE/SRP forged pistons, flat top, p/n 146998 (manuf job #178993)
|
||||
| Melling oil pump, high volume, std. pressure (40 psi), p/n M-55HV | (removed) | |||
| Melling oil pump pick-up tube: 5/8" 55-S1 | (removed) | |||
| Melling oil pump, std. volume p/n MEL-M155 | ||||
| Melling oil pump pick-up tube: MEL-155S | ||||
| Total Seal gapless second rings p/n 369003501-08 TS1 8cyl | (removed) | |||
| Total Seal gapless top rings | ||||
| Clevite 77 cam bearings p/n SH-1349 S | ||||
| Federal Mogul main bearings (Callies FM350) p/n 139 M | (removed) | |||
| Federal Mogul rod bearings (Callies FM2100) p/n 8-7100CH | (removed) | |||
| Clevite 77 main bearings MS-909 P-2 | ||||
| Clevite 77 rod bearings CB-663 P-2 | ||||
| Milodon main bearing cap stud kit | ||||
| LT-4 timing chain set | ||||
| TPIS ZZ9 cam, 212 int. 226 exh. 112 lobe sep. | (removed) | |||
| Comp Cams custom cam, 218 int. 224 exh. 114 lobe sep. | ||||
| Comp Cams custom cam, 204 int. 210 exh. 116 lobe sep. | (to be installed) | |||
| Fel-Pro gaskets | ||||
| ARP Main bearing cap stud kit p/n 234-5606 | ||||
| Heads: | ||||
| CNC ported cylinder heads: Left: 23611 / 1074 Right: 23811 / 1074 | ||||
| Rev 2.00 intake valves | ||||
| Rev 1.58 exhaust valves | ||||
| Isky Adjustable Guide Plates p/n 200-AGP | ||||
| Camp Cams Custom length pushrods 7955 7.400 .080 | ||||
| Comp Cams springs p/n 977 | ||||
| Comp Cams 7/16 x 1.90 screw-in studs (4512-16) | ||||
| Comp Cams titanium retainers | ||||
| Comp Cams 10 degree locks | ||||
| Comp Cams Pro Magnum 1.6 ratio rocker arms p/n 1305-16 | ||||
| Crane Gold Race Rockers, self aligning | (sold) | |||
| ARP Cylinder head bolt kit p/n 134-3601 | ||||
| Exhaust: | ||||
| Borla stainless steel headers & Y-Pipe | (removed) | |||
| MAC headers, Jet-Hot coated | ||||
| Borla adjustable cat back exhaust | ||||
| Induction: | ||||
| 58 mm Accel throttle body | (to be installed) | |||
| ported intake | ||||
| Ported MAF | (removed) | |||
| Powerdyne 6.5 psi supercharger | (to be installed) | |||
| K&N Air Filter | ||||
| Fuel System: | ||||
| Carroll Superfueler | (to be installed) | |||
| Inline fuel pump | (to be installed) | |||
| Drivetrain: | ||||
| GM Aluminum Driveshaft | ||||
| Tuning: | ||||
| LT-1 Edit tuning software | ||||
| Hypertech Power Programmer Plus | (removed) | |||
| Hypertech Powerstat 160 degree T-stat | (removed) | |||
| Ignition: | ||||
| Hypertech power coil | (removed) | |||
| Champion RS14YC spark plugs | ||||
| MSD 6A-BTM ignition module | (to be installed) | |||
| MSD 8mm sparkplug wires, (custom routing) | (removed) | |||
| Accel Extreme 9000 Ferro-Spiral | ||||
| MSD 90 degree sparkplug boots & terminals | (removed) | |||
| MSD 180 degree distributer boots & terminals | (removed) | |||
| Made For You Products centerbolt valve cover ignition wire looms | (removed) | |||
| Fluids: | ||||
| Mobile 1 10W-30 | ||||
| Mobile 1 M1-302 oil filter | ||||
| Mobile 1 synthetic transmission fluid | (removed) | |||
| Mobile 1 75W-90 synthetic rear axel oil | ||||
| Appearance: | ||||
| Suncoast ram-air hood | ||||
| Mallory Billet TB plate, " Supercharged" , custom painted | (to be installed) | |||
| Chrome valve covers | ||||
| Billet alternater fan & pulley, custom painted | ||||
| Tinted windows | ||||
| Bell radar detector | (removed) | |||
| G-Tech Pro / Performance Meter | ||||
| Custom black-out tail light lenses | ||||
|
|
||||
|
|
(Updated: 19 May 2008)